This is a very good start. It will have limited effectiveness depending how exactly wet the filament is though, as the diffusion speed of water in plastic is low and it takes time to get the water actually out of the center to the surface to evaporate. The few minutes a filament sits in the inline dryer might be OK for surface moisture but will fail with wetter spools.

I think the ideal system would be to have a dry box that the heating unit and fan blow into, but then feed the filament out to the printer through a “stove pipe” that acts as the dry box exhaust. This way you’re still drying the whole spool over time but then get that “final blast” to ensure the surface is as dry as possible. Make sure to insulate all walls such that you reduce how much heat you lose as the air passes through.

Damn. Proton is doing a good job of stacking up W’s these days.

I don’t doubt that rental companies have been squeezed harder and harder on licensing costs specifically to drive them out so the publisher-owned services take over

Absolutely. Don’t fuck with electrical.

Flawless statistics!

Generally speaking most buildings can be “grandfathered in” under code such that it’s perfectly legal to rent as long as the electrical system functions and meets code for the year on which it was built or installed… shitty, but legal.

Depends, generally no. Some supermarkets do as a company policy though and I choose to shop at those that do show per-unit pricing (and are also locally/employee owned)

Sorry you had to find out this way, but yes- your hip and fly is gone!

Rust desk is super based. And their software performs MILES better than Teamviewer’s shitty compression ever did.

Oh for sure, an Android OS base is fine, but it just reinforces the fact that the actual device is manufactured shovelware E-waste that could have just been an expensive app, as the hardware itself doesn’t do anything special…

No, the personal wallet lightener (it’s just a shitty android phone with no LLM running a poorly written app)

It will not affect system stability, but… Surge protectors do not work at all without a ground wire to drop excess voltage to. Any kind of line voltage disturbance could kill every device.

Additionally, without any ground wire to pull the housings of devices to ground, the potential for a short to energize the case and then electrocute you is also high.

additionally additionally, if you have grounded outlets that don’t actually have a ground connection running to them, that means either the wiring system is broken or it was “updated” by an unlicensed hack job who has undoubtedly made numerous more dangerous decisions elsewhere in the circuit.

If your house is entirely ungrounded you really should have an electrician come update it ASAP. Outlet grounds have been mandatory since 1971. The chances are high that wiring predating that code is still using old cloth-wrapped wire insulation or even knob&tube, both of which are huge fire risks as the insulation is decayed badly by now. It’s expensive to have all new wire pulled but it is necessary.

People with no internet access obviously don’t exist.

ahhh fuck I forgot about that little stupid memory bus cheat that Intel pulled. they’ve been good at obfuscating their screwing of consumers thru weird naming schemes ever since they started lol

also most of those USB adapters likely won’t support true hardware switch interrupts, Direct Memory Access, or raw bus control to talk to other cards, which almost every special ISA card actually needs at least one of these to function.

looks like the implemented CPU (ULi M6117C) supports a coprocessor interface, so it is entirely possible that a 387sx equivalent could give it floating point capabilities. it’s probably not electrically implemented on this specific device to expose the interface though. otherwise yeah no FP sucks

The point is not power but hardware compatibility. Emulation only goes so far and many, if not most, weird esoteric hardware systems from the 90s depended on idiosyncracies and strange usage of standard busses and weird interactions of the CPU. Emulation almost always breaks this.

Meta is struggling a lot less, probably because they were smart enough to lay off in one go,

or more like their user experience was already so garbage, adding AI to it doesn’t make any noticeable change lol

This is true. If you left it in the same environment it would eventually return to equilibrium and the net result would be the same. the key is that the plastic has a limited take up rate of atmospheric moisture. so if you dry it for a few hours, the water migrates out slowly, but then takes quite some time to migrate back in.

generally people either print from a dryer box or dry filaments immediately before printing.

So, if these prices can be so easily updated, surely the retailers can now include tax in the listed price. It’s very simple automated math of course…