Hi,

I just have some questions regarding 3D printing. Despite doing this for 2 years I still feel like a beginner.

Questions:

I’m looking at the Ender 5 Plus and Prusa MK3S, I’ve seen plenty of people say the Prusa is better because the Ender 5 Plus requires more “tinkering”. I just feel that the Prusa is overpriced and don’t know if I should just bite the bullet and get it or something else? I want to get back into the printing game.

I live in a trailer and my room is pretty small about 30ft x 30ft, would it be safe to use my printer in my room if all I print is PLA (I’m not talking about using it overnight either since I don’t trust it). Or should I leave it in my living room?

  • tinyVoltron@lemmy.world
    link
    fedilink
    English
    arrow-up
    5
    ·
    1 year ago

    I’ve got an Ender 5 Pro. Had it for a few years now. The tinkering factor is one of the selling points. I have learned so much about how the printer works, how electronics work in general, stepper motors, GCode, etc. Over the years I’ve upgraded everything but the frame just because I could. Get the Ender and experiment.

    • rustyriffs@lemmy.world
      link
      fedilink
      English
      arrow-up
      3
      ·
      1 year ago

      Yeah, it’s definitely a learning experience. A frustrating one, but also a rewarding one.

      I’ve had my Ender 2 pro for a couple of weeks now and just managed to get it printing good. The minimum height limitation sensor (don’t know the proper name for it) was not set correctly from the factory. It was too high, and thus my print bed was not able to be leveled correctly until I figured this out.

      Also, the slicer software I was using had a setting for “pause at layer height…” which was enabled at about 4 or 5 different times. That was super frustrating too, until I figured it out finally.

      Now my prints are looking pretty damn good, and I don’t have to babysit them. I’m pretty happy.

      • rambos@lemm.ee
        link
        fedilink
        English
        arrow-up
        2
        ·
        1 year ago

        Tbh you could experience that with many printers. You should always check your endstops/sensors/belts etc. Lose screw can make your endstop out of position and collision can happen easy. Slicer issue is simmilar thing. Not biggie, glad you sorted that.

        Best support you can get for ender is community like Lemmy (or old reddit), and its amazing support. Only thing you dont get here is replacement parts or money back

        • rustyriffs@lemmy.world
          link
          fedilink
          English
          arrow-up
          1
          ·
          1 year ago

          Yeah, I know that now! Lol

          Being brand new to everything about it, I had no idea the endstop would have been off.

          I tried to do some basic checking of things, according to some videos I watched. This one particular detail just happened to get overlooked though.

          Have you ever ran into anything that took you a while to figure out?

          • rambos@lemm.ee
            link
            fedilink
            English
            arrow-up
            1
            ·
            1 year ago

            Yeah ofc, happens all the time. Honestly, I was responding to your post so OP gets the answer, but also to stand on enders side for a change 😂

      • Thanks4Nothing@lemm.ee
        link
        fedilink
        English
        arrow-up
        2
        ·
        1 year ago

        It is tough to get support for a machine that is at your house anyways. Youtube will offer way better support for Creality and Prusa printers. You can find almost any repair you need.

      • tinyVoltron@lemmy.world
        link
        fedilink
        English
        arrow-up
        1
        ·
        1 year ago

        Google. Plenty of us out there who can help out. It never occurred toe. To contact Creality if I had a problem.